MOBOTIX M10  M10-1-45-196 Recording

General Settings  Value  Explanation  Arming Enable Off SI Closed (low) SI Open (high) CS1 CS2 CSL From Master Arm Recording: Controls camera recording: Enable: activate Recording. Off: deactivate Recording. SI: Recording armed by signal input. CS: Recording armed by custom signal as defined in General Event Settings From Master: copies Recording arming state from master camera.   (no time table) Weekdays_Mo-Fr Weekend_Sa-So Opening_Times Closing_Times MyCustomTimes Time Table Profile: Time table profile for time-controlled recording. (Time Tables) Terminate Recording (TR) Off On Activate Terminate Recording: Terminate recording if an event is detected. Use this option to freeze stored images. Click here to resume recording.   (EC - Event Counter) (EL - Event Logic) (EL2 - Event Logic 2) (PI - PIR Detector) VM - Video Motion (VM2 - Video Motion 2) (MI - Microphone) (SI - Signal Input) (SI2 - Signal Input 2) (SI3 - Signal Input 3) (SI4 - Signal Input 4) (PE - Periodic Event) (TT - Time Task) UC - User Click (BT - Button) (IR - IR Remote Control) (RC - IP Receive) (CI - Serial COM In) (TP - Temperature) (IL - Illumination) (RD - Random Event) Termination Condition: Select the events which will terminate recording. Note: Make sure that the selected event is activated in Event Settings.   Time Before Terminate: Time delay before the recording is terminated. [0..86400 s] Note: Configuring arming sources as From Master requires you to properly configure and enable Master/Slave Storage Settings  Value  Explanation  Recording (REC) Snap Shot Recording Event Recording Continuous Recording Recording Mode: Type of event and story recording. Snap Shot Recording: stores single JPEG pictures. Event Recording: stores stream files for every event using MxPEG codec. Continuous Recording: continuously streams videodata to stream files using MxPEG codec.     Pack story Pack Event Story: Pack snap shot images into one clip file to improve file server performance.   Max fps 25 fps 12 fps 6 fps 4 fps 3 fps 2 fps 1 fps 2 s 3 s 4 s 5 s Continuous Recording Frame Rate: Standard speed of continuous recording in frames per second.   Off Include audio Record Audio Data: Store audio data in stream file if available. Enable and configure microphone. Start Recording All -------------- (EC - Event Counter) (EL - Event Logic) (EL2 - Event Logic 2) (PI - PIR Detector) VM - Video Motion (VM2 - Video Motion 2) (MI - Microphone) (SI - Signal Input) (SI2 - Signal Input 2) (SI3 - Signal Input 3) (SI4 - Signal Input 4) (PE - Periodic Event) (TT - Time Task) UC - User Click (BT - Button) (IR - IR Remote Control) (RC - IP Receive) (CI - Serial COM In) (TP - Temperature) (IL - Illumination) (RD - Random Event) Start Recording: Select the events which will start recording. Use [Ctrl]-Click to select more than one event. Events in brackets need to be activated first. EC or EL for filtered events.   Snap Shot Interval: Recording interval for story images in milliseconds [0..600000 ms].   0 1 2 3 4 5 6 7 8 9 10 15 20 25 30 35 40 45 50 Pre-Alarm Images: Pre-alarm images for event story.   0 1 2 3 4 5 6 7 8 9 10 15 20 25 30 35 40 45 50 Post-Alarm Images: Post-alarm images for event story.   Max fps 25 fps 12 fps 6 fps 4 fps 3 fps 2 fps 1 fps 2 s 3 s 4 s 5 s Event Frame Rate: Recording speed if an event is detected, in frames per second.   Off 1 s 2 s Recording Time Before Event: Additional recording time before an event stream.   2 s 4 s 6 s 8 s 10 s 20 s 30 s 40 s 50 s 60 s 70 s 80 s 90 s 2 min 3 min 5 min Recording Time: Time to include in recorded stream after an event has occurred. Retrigger Recording All None -------------- (EC - Event Counter) (EL - Event Logic) (EL2 - Event Logic 2) (PI - PIR Detector) VM - Video Motion (VM2 - Video Motion 2) (MI - Microphone) (SI - Signal Input) (SI2 - Signal Input 2) (SI3 - Signal Input 3) (SI4 - Signal Input 4) (PE - Periodic Event) (TT - Time Task) UC - User Click (BT - Button) (IR - IR Remote Control) (RC - IP Receive) (CI - Serial COM In) (TP - Temperature) (IL - Illumination) (RD - Random Event) Retrigger Recording: Select the events which will retrigger recording. Use [Ctrl]-Click to select more than one event. Events in brackets need to be activated first. EC or EL for filtered events. Stop Recording All None -------------- (EC - Event Counter) (EL - Event Logic) (EL2 - Event Logic 2) (PI - PIR Detector) VM - Video Motion (VM2 - Video Motion 2) (MI - Microphone) (SI - Signal Input) (SI2 - Signal Input 2) (SI3 - Signal Input 3) (SI4 - Signal Input 4) (PE - Periodic Event) (TT - Time Task) UC - User Click (BT - Button) (IR - IR Remote Control) (RC - IP Receive) (CI - Serial COM In) (TP - Temperature) (IL - Illumination) (RD - Random Event) Stop Recording: Select the events which will stop recording. Use [Ctrl]-Click to select more than one event. Events in brackets need to be activated first. EC or EL for filtered events.   0 1 2 3 4 5 6 7 8 9 10 15 20 25 30 35 40 45 50 Images After Stop Event: Images to include in recorded snap shots after Stop Recording event has occurred.   Off 2 s 4 s 6 s 8 s 10 s 20 s 30 s 40 s 50 s 60 s 70 s 80 s 90 s 2 min 3 min 5 min Recording Time After Stop Event: Time to include in recorded stream after Stop Recording event has occurred.   Recording Dead Time: If recording is stopped by an event, a new recording is suspended for this time [0..3600 s]. Note: this dead time is started when a Stop Recording event occurs. History Recording (HR) Off Use Time Task (TT) Use Periodic Event (PE) History Recording Interval: Records one additional image at the specified interval. Event TT or PE need to be activated first. Note: The smallest interval between history images is 10 seconds.   Live Image MEGA VGA CIF Image Profile for History: Select an image profile for history recording.